Features. • Full DTMF receiver. • Less than 35mW power consumption. • Industrial temperature range. • Uses quartz crystal or ceramic. CMPI datasheet, CMPI circuit, CMPI data sheet: CALMIRCO – CMOS Integrated DTMF Receiver,alldatasheet, datasheet, Datasheet search site . comCMOS Integrated DTMF Receiver datasheet search, datasheets, Datasheet search CMPI Datasheet(PDF) 1 Page – California Micro Devices Corp.
|Published (Last):||10 March 2004|
|PDF File Size:||9.35 Mb|
|ePub File Size:||5.48 Mb|
|Price:||Free* [*Free Regsitration Required]|
California Micro Devices Corp
Guard time adjustment also allows the designer to tailor system parameters such as talk-off and noise immunity. Any subsequent loss of signal condition will cause ESt to fall. GT continues to drive high as long as ESt remains high, signaling that a received tone pair has been registered. Design information for guard time adjustment is shown in Figure 5. The bandwidths of these filters correspond to the bands enclosing the datasueet and high-group tones See Figure 3. The on-chip clock generator requires only a low cost TV crystal or ceramic resonator as an external component.
In situations which do not require independent selection of. The internal clock circuit is completed with the addition of a. A typical circuit using this steering configuration is shown in. Increasing t REC improves talk-off performance, since it reduces. The on-chip clock generator dataseet only a low cost TV. A value for C of 0. GT continues to drive high as long as ESt remains high.
This may be necessary to meet system specifications which. Component values are chosen according to the following formula: Different steering arrangements may be used to select independently the guardtimes for tone-present t GTP and tone absent t GTA. The filter section uses a switched capacitor technique for both high and low group filters and dial tone rejection. The timing requirements for most telecommunica.
Each filter output is followed by a.
CMPI Datasheet PDF – California Micro Devices => Onsemi
This check is performed by an. When the detector recognizes the simultaneous presence of.
Signal limiting is performed by high- gain comparators. The contents of the output latch are made available on the 4-bit output bus by raising the three-state control input TOE to a logic high. Thus, as well as rejecting signals too short to be considered valid, the receiver will tolerate signal interruptions drop outs too short to be considered a valid pause. Provision is made for connection of a feedback resistor to the. The timing requirements for most telecommunica- tion applications are satisfied with this circuit.
These comparators are provided with a hysteresis to prevent detection of unwanted low-level signals and noise.
This DTMF receiver minimizes external component count by providing an on-chip differential input ampli. Providing signal condition is maintained ESt remains high for.
CMPI datasheet,datasheets manu Page:2==DTMF接受解码电路==[未知厂家] pdf datenblatt – –
The steering circuit works in reverse to validate the. C Providing signal condition is maintained ESt remains high for the validation period tV reaches the threshold V of GTP C TSt the steering logic to register the tone pair, thus latching its corresponding 4-bit code See Figure 2 into the output latch. The filter section also incorporates notches at Hz and Hz which provides excellent dial tone rejection.
OSC3 that can be used to drive clock inputs of other devices.
A typical circuit using this steering configuration is shown in Figure 1. Clock Circuit The internal clock circuit is completed with the addition of a standard television color burst crystal or ceramic resonator having a resonant frequency of 3.
Guard Time Adjustment In situations which do not require independent selection of receive and pause, the simple steering circuit of Cm8780pi 4 is applicable.
The filter section also. Provision is made for connection of a feedback resistor to the op-amp output GS for adjustment of gain. The bandwidths of these.
This check is performed by an external RC time constant driven by E St. These comparators are provided with a. The outputs of the comparators provide full-rail.
V REF which is used to bias the inputs at mid-rail. A complex averaging algorithm is used to protect against tone simulation by extraneous signals such as voice while providing tolerance to small frequency variations. Separation of the low-group and high-group tones is achieved. On the other hand, a relatively short t Ck8870pi with a long t Dafasheet would be appropriate for extremely noisy environments where fast acquisition time and immunity to drop-outs would be require- ments.
Thus, as well as rejecting. Figure 6 shows the.