Designed for the contractor, the CPS MK II feature 2-RU chassis, Phoenix-type connectors for inputs and outputs, pre-programmable power-on delay, easy power-on via remote contact closures, rear panel attenuators, and a switchable 50 Hz high-pass filter. Like the CPS multi. Two-Channel Models CPS, CPS, CPS, and CPS CPS2.x rear view. Remote power-on contact. 1. Programmable power-on timer. 2. Module slot for. Buy Electro-Voice CPS 2-Channel Power Amplifier for RCM IRIS-Net Remote Control Module (W, 4 Ohms) Review Electro-Voice CPS
|Published (Last):||24 July 2017|
|PDF File Size:||20.29 Mb|
|ePub File Size:||2.26 Mb|
|Price:||Free* [*Free Regsitration Required]|
Level Indicators for channels 1 and 2 2. Do not use the power amplifier near heat sources, like heater blowers, stoves or any other heat radiating devices.
Electro-Voice CPS 2-Channel Power Amplifier FU B&H
Set the switch to the 50 Cpz2.9 position for activating the High Pass Filter. Amplification is set via input level control of channel 1 only.
This indicates all protections are working fine. Unbalanced connections should only be used if the cables are very short and no interfering signals are to be expected in the vicinity of the power amplifier.
CPS 2.4 MK II
The audio signal has to be applied to the input connectors of channel 1, amplification is set via input level control of channel 1 only.
Please read and follow the instructions provided in the documentation that you have received together with each extension module. When installing the power amp in a case or rack system, attention should be paid to these details to provide sufficient ventilation. The amount of heat resulting from power dissipation might remain dps2.9 of a rack-shelf and needs to be diverted using ccps2.9 measures.
Introduction 1 Introduction 1. Got it, continue to print.
CPS MK II Contractor Precision Series Class‑H Power Amplifier by Electro‑Voice
For fixed amplifier installations in a device control room that incorporate a central air-cooling system or air conditioners, calculating the c;s2.9 heat emission may be necessary.
Brackets for securing the power amplifier are available as accessories. Set the switch to the OFF position if no attenuation of low frequency audio signals is required.
As with all Electro-Voice power amps with fan cooling, the eev direction is front-to-rear, obviously because there is more cold air outside of the rack case than inside. Unbalanced connections should only be used if the cables are very short and no interfering signals are to be expected in the vps2.9 of the power amplifier.
Connect the power amplifier only to a mains network, which corresponds to the requirements indicated on the type plate. In general, setting up or mounting the power amplifier has to be done in a way that cpa2.9 air can enter unhindered at the front and exhausted air can exit at the rear.
Keep ventilation louvers free from dust to ensure unhindered airflow. PARALLEL operation is the mode of choice, whenever the same input signal drives multiple power amp channels of a large system installation.
The power drawn from the mains network is converted into output power to feed the connected loudspeaker systems and into heat. Controls, Indicators and Connections Front View 1.
In DUAL mode, the two channels of the power amplifier work independent from each other. Electrovoice contractor precision cps1: Speaker system switch-on is delayed by approximately 2 seconds via output relays, effectively suppressing any possible power-on noise, which otherwise might be heard through the loudspeakers.
To print the manual completely, please, download it.
Enter text from picture: During installation, always separate the power amplifier c;s2.9 the mains. This manual also for: F reserved Table 4. The power amplifier remains cooler and dissipating the developing waste heat in a specific direction gets easier. Also See for CPS2.
CPS 2.9 MK II
Please take time to consult this manual so that you can understand all the features built into your Electro-Voice amplifier and fully utilize all its performance capabilities. Following table shows possible switch settings and corresponding delay times. Additionally securing the amplifier at the rear becomes necessary, if the rack case in which the power amplifier has been installed will e transported.
Do not use the power amplifier near heat sources, like heater blowers, stoves or any other heat radiating devices.
The audio signal has to be applied to the input connectors of channel 1. A soft start circuit compensates mains inrush current peaks and thus prevents triggering AC mains fuse when switching on the amplifier.